sedanman
11-01-2004, 04:27 PM
Romac 50 oz balancer steel outside hub about two years old $110.
70mm Acufab TB and spacer $150
DSS stud girdle with all the hardware, clearanced for a dipstick in stock style. $200
I have crane gold rocker arms 7/16's in 1.65 ratio, not many miles at all. $200
I have a set of trickflow heads, they were ported by CFM performance out of indy. Most of the work was done on the exhaust port for a power adder car without a big cam (I will post the flow numbers soon) they have 7/16 stud mounts on them but I allso have 3/8 to go with it. The heads were freshend up when they were ported about 3,000 miles ago. Also comes with the reqiured length hardened pushrods from trickflow.
$1000 obo +shipping
Front brakes form a fox 73mm calipers, all steel braided lines, hawk pads, power slot rotors $150.
I have a COMPLETE black interior from a 91 coupe. It is in very good condition overall no seat lean the ash tray door works and is not broken! The top to the center console has the clip broken off and there are two 3/4 inch cuts in the back seat that you can hardly see. The buyer is welcome to come and take the interior out with me so they can verify that EVERYTHING is their.
$1,000
Welds (15X8 5.5bs) with 26X10 MT ET Drags 80% tread
and 15X3.5's with 165R15's on them, 4lug $500+ shipping.
Spec AL flywheel has about 200 miles tops $200
Liberty pro-shifted TKO, Lakewood bell, Revlock clutch, Triax shifter (and original) and AL driveshaft for a TKO $1800
50# injectors and 83MM pro M $425+shipping
GSS340 fuel pump about 1500 miles on it $75 plus shipping.
Complete fuel system:
Cartek intank pickup that has been modified to allow more flow it then goes -10 out into a aeromotive 100micron filter into a aeromotive 1000A pump then into a 10micron filter then -10 up to a y-block that splits two -8's into downs fuel rails then out twin -6's to a aeromotive regulator that feeds -8 back then it necks to -6 to plug back into the pickup.
It has been on the car for about a 100 miles, the pump and regulator and rails have about 500 more miles on them.
$1000+ shipping
Full exhaust, BBK 1 5/8 longtube headers, H-pipe, mac produmps. $375
Digital 6 about two years old 3,000 miles or so comes with harness $200
MSD BTM $115
Feel free to call me at 317-340-4973 or e-mail at sedanman91@yahoo.com
Will take trades for 03-04 cobra parts.
70mm Acufab TB and spacer $150
DSS stud girdle with all the hardware, clearanced for a dipstick in stock style. $200
I have crane gold rocker arms 7/16's in 1.65 ratio, not many miles at all. $200
I have a set of trickflow heads, they were ported by CFM performance out of indy. Most of the work was done on the exhaust port for a power adder car without a big cam (I will post the flow numbers soon) they have 7/16 stud mounts on them but I allso have 3/8 to go with it. The heads were freshend up when they were ported about 3,000 miles ago. Also comes with the reqiured length hardened pushrods from trickflow.
$1000 obo +shipping
Front brakes form a fox 73mm calipers, all steel braided lines, hawk pads, power slot rotors $150.
I have a COMPLETE black interior from a 91 coupe. It is in very good condition overall no seat lean the ash tray door works and is not broken! The top to the center console has the clip broken off and there are two 3/4 inch cuts in the back seat that you can hardly see. The buyer is welcome to come and take the interior out with me so they can verify that EVERYTHING is their.
$1,000
Welds (15X8 5.5bs) with 26X10 MT ET Drags 80% tread
and 15X3.5's with 165R15's on them, 4lug $500+ shipping.
Spec AL flywheel has about 200 miles tops $200
Liberty pro-shifted TKO, Lakewood bell, Revlock clutch, Triax shifter (and original) and AL driveshaft for a TKO $1800
50# injectors and 83MM pro M $425+shipping
GSS340 fuel pump about 1500 miles on it $75 plus shipping.
Complete fuel system:
Cartek intank pickup that has been modified to allow more flow it then goes -10 out into a aeromotive 100micron filter into a aeromotive 1000A pump then into a 10micron filter then -10 up to a y-block that splits two -8's into downs fuel rails then out twin -6's to a aeromotive regulator that feeds -8 back then it necks to -6 to plug back into the pickup.
It has been on the car for about a 100 miles, the pump and regulator and rails have about 500 more miles on them.
$1000+ shipping
Full exhaust, BBK 1 5/8 longtube headers, H-pipe, mac produmps. $375
Digital 6 about two years old 3,000 miles or so comes with harness $200
MSD BTM $115
Feel free to call me at 317-340-4973 or e-mail at sedanman91@yahoo.com
Will take trades for 03-04 cobra parts.